MT0950 RDD

Plastic cover RDD – cover with hinge in the outer radius

Properties

Plastic cover system with hinge for light and medium loads. Assembly without screws.
Available customized in 16 mm sections.
Outside: swivable to both sides.
Inside: release by turning 90°.

Stay arrangement on each chain link (VS: fully-stayed)

B_i 77 – 349 mm in 16 mm width sections

All pictographs

Dimensions

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	h_G' [mm]	h_G' Offroad [mm]	B_k [mm]	B_EF [mm]	q_k [kg/m]
95	54.5	80	83.5	86	B_i + 39	B_i + 39	4.30 – 7.70

^* in 16 mm width sections

B_i [mm]
77	93	109	125	141	157	173	189	205	221
237	253	269	285	301	317	333	349

KR [mm]
140	170	200	260	290	320	380

Order example

MT0950

Type

269

B_i [mm]

RDD

Stay variant

200

KR [mm]

2850

L_k [mm]

Stay arrangement

Our technical support can provide help for gliding arrangements: technik@kabelschlepp.de

Inner distribution

Divider systems

As a standard, the divider system is assembled at every 2^nd chain link.

For applications with lateral acceleration and laying on the side, the dividers or the complete divider system (dividers with height separations) are fixed in the cross section. The arresting cams click into place in the locking grids in the crossbars (version B).

Divider system TS0

without height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	22.5	16	10	16	–

The dividers are fixed in the cross section (version B).

Divider system TS1

with continuous height separation

Vers.	a_{T min} [mm]	a_{T max} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	22.5	22.5	16	10	16	2

The dividers are fixed in the cross section (version B).

Divider system TS2

with partial height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	22.5	16^*/32	10^*/26	16	2

^* for VR0

With grid distribution (16 mm grid). The dividers are fixed by the height separation, the grid is fixed in the cross section (version B).

Divider system TS3

with height separation made of plastic partitions

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
B	6.5	16/42^*	8	2

^* for aluminum partitions

The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.

Aluminum partitions in 1 mm width sections with a_x > 42 mm are also available.

a_x (center distance of dividers) [mm]
a_c (nominal width of inner chamber) [mm]
16 8	32 24	48 40	64 56	80 72	96 88	112 104	128 120	144 136	160 152	176 168	192 184
208 200

When using plastic partitions with a_x > 112 mm, we recommend an additional center support with a twin divider (S_T = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.

Order example

TS3

Divider system

Version

n_T

Chamber

a_x

VR1

VR3

Height separation

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [n_T ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [a_T/a_x] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

Universal end connectors UMB – plastic (standard)

The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.

Recommended tightening torque: 27 Nm for cheese-head screws ISO 4762 - M8 - 8.8

MT0950 Universal end connectors UMB - plastic

Connection point

F – fixed point
M – driver

Connection type

U – universal end connector

End connectors – plastic/steel

Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

A – connection surface outside
I – connection surface inside

Order example

Plastic/Steel

UMB

End connector

Connection point

Connection type

Connection surface

End connector

Plastic/Steel

UMB

Connection point

Connection type

Connection surface

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

MT series – Variable, closed cable carrier with extensive range of accessories

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE^® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE^®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX^® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX^®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator

Product Configurator

Efficient, quick and complete configuration the result is your individual product with an excellent price-performance ratio
Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal

Product Configurator