to top Arrow Up

MK0950 RD

Plastic stay RD – Frame stay with hinge

mk0950-rd_start.png

Properties

  • Plastic profile bars with hinge for light to medium loads. Assembly without screws.
  • Available customized in 16 mm grid.
  • Outside: swivable to both sides.
  • Inside: release by turning by 90°.
test
Stay arrangement on every 2<sup>nd</sup> chain link

Stay arrangement on every 2nd chain link, standard (HS: half-stayed)

Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 16 mm increments
Bi 45 – 557 mm in 16 mm width sections

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Important information

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
t
[mm]
hi
[mm]
hG
[mm]
hG'
[mm]
hG' Offroad
[mm]
Bk
[mm]
BEF
[mm]
qk
[kg/m]
95588083.586Bi + 39Bi + 393.00 – 6.20
* in 16 mm width sections
Bi
[mm]
45617793109125141157173189
205221237253269285301317333349
365381397413429445461477493509
525541557
KR
[mm]
140170200260290320380
Order example
Order code

MK0950

413

RD

200

2850

HS

Our technical support can provide help for gliding arrangements: technik@kabelschlepp.de

Inner distribution

Divider systems

As a standard, the divider system is mounted on each crossbar – for stay mounting on every 2nd chain link (HS).
As a standard, dividers and the complete divider system (dividers with height separations) can be moved in the cross section (version A).

The dividers are easily attached to the stay for applications with lateral acceleration and for applications laying on their side by simply turning the frame stay by 180°. The arresting cams click into place in the locking grids in the crossbars (Version B). The groove in the frame stay faces outwards.

Divider system TS0

without height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A5.514.58.5
B6.5161016

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS0

Divider system TS1

with continuous height separation
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A5.52514.58.52
B6.5251610162

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS1

Divider system TS2

with partial height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A5.514.5*/218.5*/152
B6.516*/3210*/26162

* for VR0

With grid distribution (16 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section (version A) or fixed (version B).

Divider system TS2

Divider system TS3

with height separation made of plastic partitions
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A416/42*82

* for aluminum partitions

The dividers are fixed by the partitions, the complete divider system is movable in the cross section.

Divider system TS3
Divider system TS3

Aluminum partitions in 1 mm width sections with ax > 42 mm are also available.

ax (center distance of dividers) [mm]
ac (nominal width of inner chamber) [mm]
16
8
18
10
23
15
28
20
32
24
33
25
38
30
43
35
48
40
58
50
64
56
68
60
78
70
80
72
88
80
96
88
112
104
128
120
144
136
160
152
176
168
192
184
208
200

When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.

Order example
Order code

TS3

A

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

M0950 End Connector UMB
Important information

Recommended tightening torque: 27 Nm for cheese-head screws ISO 4762 - M8 - 8.8

M0950 End Connector UMB
Connection point

F – fixed point
M – driver

Connection type

U – universal mounting bracket

M0950 End Connector
M0950 End ConnectorM0950 End Connector
Connection point

– fixed point
– driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside

Connection surface

– connection surface inside
– connection surface outside

Order example
Order code

Plastic/steel

F

A

U

UMB

M

U

 

End connector

Plastic/steel

UMB

Connection point

F

M

Connection type

A

U

Connection surface

U

Important information

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

Subject to change.
Contact
Please contact us:
Your contact: