TKA30.060

Stay variant 060 – covered on both sides with inside detachable cover

Properties

Plastic cover for rough environmental conditions with dirt, chips or spray water.
Fully detachable on one side in any position.
Inside: very quick release.

Stay arrangement on each chain link (VS: fully-stayed)

B_i 15 – 65 mm

All pictographs

Dimensions

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	B_k [mm]	q_k [kg/m]
30.5	20.5	28.5	B_i + 13	0.48 – 0.76

B_i [mm]
15	20	25	38	50	65

KR [mm]
55	75	95	125	145	180

Order example

TKA30

Type

060

Stay variant

B_i [mm]

125

KR [mm]

915

L_k [mm]

Stay arrangement

Our technical support can provide help for gliding arrangements: technik@kabelschlepp.de

Inner distribution

Divider systems

The divider system is mounted on every 2^nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (Version A).

The dividers are easily attached to the stay for applications with transverse accelerations and for applications laying on the side by simply turning them.
The locking cams click into place in the locking grids in the covers (Version B).

Divider system TS0

without height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
A	3.5	7	5	–	–
B	A	8	6	2	–

B_i [mm]

a_{T min} [mm]

7.5

8.5

Divider system TS1

with continuous height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
A	3.5	7	5	–	2
B	A	8	6	2	2

B_i [mm]

a_{T min} [mm]

7.5

8.5

Order example

TS1

Divider system

Version

n_T

VD0

VD1

Height separation

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [n_T].

If using divider systems with height separation (TS1), please also state the positions [e.g. VD1] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

Universal end connectors UMB – plastic (standard)

The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom, or face on.

Recommended tightening torque: 3 Nm for cheese-head screws ISO 4762 - M4 x 12

The end connectors are also available as an option without cover sheets. Please state when ordering.

TKA30 Universal-Anschlusselemente UMB – Kunststoff (Standard)

Connection point

F – fixed point
M – driver

Connection type

U – universal end connector

Order example

UMB

End connector

Connection point

Connection type

End connector

UMB

Connection point

Connection type

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

TKA series – Chip-tight right to the end

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE^® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE^®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX^® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX^®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator

Product Configurator

Efficient, quick and complete configuration the result is your individual product with an excellent price-performance ratio
Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal

Product Configurator