MT1250 RMD

Aluminum cover RMD– cover with hinge in the outer radius

Vlastnosti

Aluminum cover system with hinge for light and medium loads. Assembly without screws.
Available customized in 1 mm sections.
Outside: swivable to both sides.
Inside: release by turning 90°.

Stay arrangement on each chain link (VS: fully-stayed)

B_i von 150 – 800 mm im 1 mm mriežka

Všetky piktogramy

Rozmery

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

For rough environmental conditions, we recommend the use of OFFROAD glide shoes with 80 % higher wear volume.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	h_G' [mm]	h_G' Offroad [mm]	B_i [mm] ^*	B_k [mm]	B_EF [mm]	q_k [kg/m]
125	68,5	96	99,5	103	150 – 800	B_i + 45	B_i + 45	9,29 – 26,34

^* v m šírky

KR [mm]
260	300	340	380	500

Príklad objednania

MT1250

Typový rad

600

B_i [mm]

RMD

Konštrukcia mostíka

300

KR [mm]

4250

L_k [mm]

Usporiadanie mostíka

Pri posuvnom prevedení využite našu technickú podporu: info@kabelschlepp.sk

Vnútorné rozdelenie

Systémy oddeľovacích mriežok

As a standard, the divider system is mounted on every 2^nd chain link.

As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

Divider system TS0

without hight separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	6	12	8	–

The dividers can be moved in the cross section.

Divider system TS1

with continuous height spearation

Verzia	a_{T min} [mm]	a_{T max} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	6	25	12	8	2

The dividers can be moved in the cross section.

Divider system TS2

with partial height separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	7	21	15	2

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Sliding dividers are optionally available (thickness of divider = 4 mm)

Príklad objednania

TS2

Systém mriežok

Verzia

n_T

Komora

a_x

VR1

VR3

výškové rozdelenie

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [n_T]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [a_T/a_x] (as seen from the driver).

If using divider systems with height separation (TS1 – TS2), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.

Pripojovacie prvky

Universal end connectors UMB - plastic (standard)

The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.

Recommended tightening torque: 54 Nm for cheese-head screws ISO 4762 - M10 - 8.8

MT1250 Universal connection element UMB - plastic

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

U – universal end connector

End connectors – plastic/steel

Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Pripojovacia plocha

I – connection surface inside
A – connection surface outside

Príklad objednania

Plastic/steel

UMB

pripojeniesprvok

pripojeniebod

Spôsob pripojenia

Pripojovacia plocha

pripojeniesprvok

Plastic/steel

UMB

pripojeniebod

Spôsob pripojenia

Pripojovacia plocha

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

MT series – Variable, closed cable carrier with extensive range of accessories

K tomu patrí

Vodiče pre nosiče energie – TRAXLINE®

Spoľahlivý, robustný s vysokou dostupnosťou. Profitujte z dlhoročných skúseností a z priebežnej optimalizácie overenou počas testov i v praxi. TRAXLINE^® vodiče pre kompetentné systémové poradenstvo ako aj servis po celom svete.

na TRAXLINE^®

Systémy nosičov energií pripravené na zapojenie – TOTALTRAX®

Od samostatných vedení až po komplexné systémy pripravené na zapojenie, v počte 1 až po série - po celom svete sú v nasadení tisícky osvedčených systémov. Prednosti TOTALTRAX^® systémov sú zjavné: jedna kontaktná osoba, jedno objednávacie číslo, dodávka just in time na želané miesto, krátke prestoje vďaka Plug & Play montáži.

na TOTALTRAX^®

Príslušenstvo

Spoľahlivé odvíjanie a optimálne kĺzanie pri dlhých pojazdoch

na Podporné kanály
na Vodiace kanály

Na optimálne umiestnenie pri dynamickom použití káblov

k Odľahčenie v ťahu

Služby

Konfigurátor produktu

Konfigurátor produktu

Konfigurovať efektívne, rýchlo a kompletne – výsledkom bude Váš systém nosičov energie s optimálnym pomerom cena / výkon
Online Konfigurátor produktuEngineer + zodpovedajúce CAD modely CADbez zmeny platformy

Konfigurátor produktu