S/SX1250 RV

Aluminum stay RV – reinforced frame stay

Vlastnosti

Aluminum profile bars for medium to heavy loads and large cable carrier widths. Double threaded joint on both sides.
Available customized in 1 mm grid.
Inside/outside: Threaded joints easy to release.

Stay arrangement on every 2^nd chain link, standard (HS: half-stayed)

Stay arrangement on each chain link (VS: fully-stayed)

B_k von 200 – 600 mm v 1 mm mriežka

Všetky piktogramy

Rozmery

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	h_G' [mm]	B_i [mm]	B_St [mm] ^*	B_k [mm]	B_EF [mm]	q_k [kg/m]
125	72	94	104	154 – 554	176 – 576	B_St + 24	B_St + 30	13,83 – 17,11

^* v m šírky

KR [mm]
145	200	220	260	300	340	380	420	460	500	540	600	1000

Príklad objednania

S1250

Typový rad

400

B_St [mm]

Konštrukcia mostíka

200

KR [mm]

Materiál

4750

L_k [mm]

Usporiadanie mostíka

Pri posuvnom prevedení využite našu technickú podporu: info@kabelschlepp.sk

Vnútorné rozdelenie

Systémy oddeľovacích mriežok

The divider system is mounted on each crossbar as a standard – on every 2^nd chain link for stay mounting (HS – half-stayed).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

Divider system TS0

without height separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	16	10	–

The dividers can be moved in the cross section.

Divider system TS1

with continuous height separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	16	10	2

The dividers can be moved in the cross section.

Divider system TS2

with partial height separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	21	15	2

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Sliding dividers are optionally available (thickness of divider = 6 mm).

Divider system TS3

with height separation consisting of plastic partitions

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	4	16/42^*	8	2

^* for aluminum partitions

The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.

Aluminum partitions with 1 mm increments with a_x > 42 mm are also available.

a_x (vzdialenosť stredov deliacich priečok) [mm]
a_c (užitočná šírka vnútornej komory) [mm]
16 8	18 10	23 15	28 20	32 24	33 25	38 30	43 35	48 40	58 50	64 56	68 60
78 70	80 72	88 80	96 88	112 104	128 120	144 136	160 152	176 168	192 184	208 200

When using plastic partitions with a_x > 112 mm, we recommend an additional center support with a twin divider (S_T = 4 mm). Twin dividers are also suitable for retrofitting in the partition system.

Príklad objednania

TS3

Systém mriežok

Verzia

n_T

Komora

a_x

VR1

VR3

výškové rozdelenie

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [n_T ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [a_T/a_x] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.
The end dividers are part of the divider system and don‘t have to be ordered separately.

Pripojovacie prvky

End connectors – steel

End connectors made of steel. The connection variants on the fixed point and on the driver can be combined and changed later on, if necessary.

Caution: The standard connection variant FAI/MAI is only possible from B_k of 125 mm.

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

A – threaded joint to outside (standard)
I – threaded joint to inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside

Pripojovacia plocha

I – connection surface inside
A – connection surface outside

Príklad objednania

Steel

pripojeniesprvok

pripojeniebod

Spôsob pripojenia

Pripojovacia plocha

pripojeniesprvok

Steel

pripojeniebod

Spôsob pripojenia

Pripojovacia plocha

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

S/SX series – Extremely robust and sturdy steel cable carriers

K tomu patrí

Vodiče pre nosiče energie – TRAXLINE®

Spoľahlivý, robustný s vysokou dostupnosťou. Profitujte z dlhoročných skúseností a z priebežnej optimalizácie overenou počas testov i v praxi. TRAXLINE^® vodiče pre kompetentné systémové poradenstvo ako aj servis po celom svete.

na TRAXLINE^®

Systémy nosičov energií pripravené na zapojenie – TOTALTRAX®

Od samostatných vedení až po komplexné systémy pripravené na zapojenie, v počte 1 až po série - po celom svete sú v nasadení tisícky osvedčených systémov. Prednosti TOTALTRAX^® systémov sú zjavné: jedna kontaktná osoba, jedno objednávacie číslo, dodávka just in time na želané miesto, krátke prestoje vďaka Plug & Play montáži.

na TOTALTRAX^®

Príslušenstvo

Spoľahlivé odvíjanie a optimálne kĺzanie pri dlhých pojazdoch

na Podporné kanály
na Vodiace kanály

Na optimálne umiestnenie pri dynamickom použití káblov

k Odľahčenie v ťahu

Služby

Konfigurátor produktu

Konfigurátor produktu

Konfigurovať efektívne, rýchlo a kompletne – výsledkom bude Váš systém nosičov energie s optimálnym pomerom cena / výkon
Online Konfigurátor produktuEngineer + zodpovedajúce CAD modely CADbez zmeny platformy

Konfigurátor produktu