Q100 RV

Aluminum stay RV – Frame stay reinforced

Vlastnosti

Aluminum profile bars with plastic adapter for medium to high loads and large cable carrier widths. Assembly without screws.
Available customized in 1 mm sections.
Outside/inside: release by rotating 90°.

Stays on every 8^th section, standard (HS: half-stayed)

Stays on every 4^th section (VS: fully-stayed)

B_i von 70 – 600 mm im 1 mm mriežka

Všetky piktogramy

Rozmery

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

Number of glide shoes: Pitch per cable carrier length/4 x 2 -2

t [mm]	h_i [mm]	h_G [mm]	h_G' [mm]	B_i [mm] ^*	B_k [mm]	B_EF [mm]	q_k [kg/m]
30	72	98	108	70 – 600	B_i + 82	B_i + 89,5	2,80 – 4,60

^* v m šírky

KR [mm]
180	250	300	370	460	600

Príklad objednania

Q100

Typový rad

400

B_i [mm]

Konštrukcia mostíka

370

KR [mm]

1860

L_k [mm]

Usporiadanie mostíka

Pri posuvnom prevedení využite našu technickú podporu: info@kabelschlepp.sk

Vnútorné rozdelenie

Systémy oddeľovacích mriežok

The divider system is mounted on each crossbar as a standard – on every 8^th section for stay mounting (HS).
As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (Version A).

Divider system TS0

without hight separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	16	10	2

The dividers can be moved in the cross section.

Divider systems TS1

with continuous height separation

Verzia	a_{T min} [mm]	a_{T max} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	25	16	10	2

The dividers can be moved in the cross section.

Divider system TS2

with partial height separation

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	13	21	15	2

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Sliding dividers are optionally available (thickness of divider = 6 mm).

Divider system TS3

with height separation consisting of plastic partitions

Verzia	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	n_{T min}
A	8	16/ 42^*	8	2

^* for aluminum partitions

The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.

Aluminum partitions in 1 mm width sections with a_x > 42 mm are also available.

a_x (vzdialenosť stredov deliacich priečok) [mm]
a_c (užitočná šírka vnútornej komory) [mm]
16 8	18 10	23 15	28 20	32 24	33 25	38 30	43 35	48 40	58 50	64 56	68 60
78 70	80 72	88 80	96 88	112 104	128 120	144 136	160 152	176 168	192 184	208 200

When using plastic partitions with a_x > 112 mm, we recommend an additional center support with a twin divider (S_T = 4 mm). Twin dividers are also suitable for retrofitting in the partition system. The height separations VR8 and VR9 are not possible when using twin dividers.

Príklad objednania

TS3

Systém mriežok

Verzia

n_T

Komora

208

a_x

VR1

VR9

výškové rozdelenie

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [n_T ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [a_T/a_x] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

Pripojovacie prvky

Universal connection element UMB - plastic (standard)

The universal end connectors (UMB) are made from plastic and can be mounted from the top, from the bottom, face on or from the side.

Q100 Universal connection element UMB - plastic

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

U – universal end connector

Príklad objednania

UMB

pripojeniesprvok

pripojeniebod

Spôsob pripojenia

pripojeniesprvok

UMB

pripojeniebod

Spôsob pripojenia

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

QUANTUM® series – Light, extremely quiet and low-vibration for high speeds and accelerations

K tomu patrí

Vodiče pre nosiče energie – TRAXLINE®

Spoľahlivý, robustný s vysokou dostupnosťou. Profitujte z dlhoročných skúseností a z priebežnej optimalizácie overenou počas testov i v praxi. TRAXLINE^® vodiče pre kompetentné systémové poradenstvo ako aj servis po celom svete.

na TRAXLINE^®

Systémy nosičov energií pripravené na zapojenie – TOTALTRAX®

Od samostatných vedení až po komplexné systémy pripravené na zapojenie, v počte 1 až po série - po celom svete sú v nasadení tisícky osvedčených systémov. Prednosti TOTALTRAX^® systémov sú zjavné: jedna kontaktná osoba, jedno objednávacie číslo, dodávka just in time na želané miesto, krátke prestoje vďaka Plug & Play montáži.

na TOTALTRAX^®

Príslušenstvo

Spoľahlivé odvíjanie a optimálne kĺzanie pri dlhých pojazdoch

na Podporné kanály
na Vodiace kanály

Na optimálne umiestnenie pri dynamickom použití káblov

k Odľahčenie v ťahu

Služby

Konfigurátor produktu

Konfigurátor produktu

Konfigurovať efektívne, rýchlo a kompletne – výsledkom bude Váš systém nosičov energie s optimálnym pomerom cena / výkon
Online Konfigurátor produktuEngineer + zodpovedajúce CAD modely CADbez zmeny platformy

Konfigurátor produktu