UA1665.RMA

Stay variant RMA – Mounting frame stay

Vlastnosti

Weight-optimized plastic frame with particularly high torsional rigidity.
Plastic crossbars and aluminum profile bars with plastic mounting frame stays for guiding very large cable diameters.
Outside/inside: threaded joint easy to release.

Stay arrangement on each chain link (VS: fully-stayed)

B_i von 125 – 200 mm

Všetky piktogramy

Rozmery

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	B_k [mm]	B_EF [mm]	q_k (RVAI)^* [kg/m]	q_k (RVAO)^* [kg/m]
66,5	44	60	B_i + 22	B_i + 27	3,10 – 3,95	3,58 – 4,66

B_i [mm]
125	150	175	200

H_i [mm]
114	139	164	189

KR [mm]
75	100	120	140	200	250	300

* indicated according to standard pitch

Príklad objednania

UA1665

Typový rad

030

Konštrukcia mostíka

150

B_i [mm]

140

KR [mm]

2660

L_k [mm]

RVAO

Usporiadanie mostíka

Pri posuvnom prevedení využite našu technickú podporu: info@kabelschlepp.sk

Assembly variants

RMAI – assembly to the inside:
standard pitch, mounting frame stay on every 4th stay, no screw fixing. Gliding application is not possible when using assembly version RVAI.
Observe minimum KR:
H_i = 114 mm: KR_min   = 200 mm
H_i = 139 mm: KR_min   = 250 mm
H_i = 164 mm: KR_min   = 300 mm
H_i = 189 mm: KR_min   = 300 mm

RMAO – assembly to the outside:
standard pitch, mounting frame stay on every 2^nd stay, screw fixing.
cable carrier rests on the bars. A bracket must be provided for the fixed point.
Guiding in a channel is required for support. Please contact our technical support at technik@kabelschlepp.de to find the corresponding guide channel.
Please note the operating and installation height.

Cross section mounting frame stay

To achieve a nearly square cross section in the mounting frame stay, we recommend the following combination of B_iand H_i:

B_i [mm]	H_i [mm]	KR_min [mm]	Stays [mm]
125	114	200	100
150	139	250	125
175	164	300	150
200	189	300	175

Pripojovacie prvky

Universal end connectors UMB – plastic (standard)

The universal mounting brackets (UMB) are made from plastic and can be mounted from above, from below or on the face side.

Recommended tightening torque:
5 Nm for screws M5 - 8.8

B_i [mm]	n_z
50	2 x 3
75	2 x 5
100	2 x 7
125	2 x 9
150	2 x 11
175	2 x 13

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

U – universal mounting bracket

Príklad objednania

UMB

pripojeniesprvok

pripojeniebod

Spôsob pripojenia

pripojeniesprvok

UMB

pripojeniebod

Spôsob pripojenia

We recommend the use of strain reliefs at the driver and fixed point.

Single-part end connectors – plastic

The plastic end connectors can be connected from above or below. The connection type can be changed by altering the position of the end connector.

Recommended tightening torque: 15 Nm for screws M8 - 8.8

B_i [mm]	n_z
50	2 x 4
75	2 x 6
100	2 x 8
125	2 x 10
150	2 x 12
175	2 x 14
200	2 x 16
225	2 x 18
250	2 x 20

Bod pripojenia

F – fixed point
M – driver

Spôsob pripojenia

A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside

Príklad objednania

End connector

pripojeniesprvok

pripojeniebod

Spôsob pripojenia

pripojeniesprvok

End connector

pripojeniebod

Spôsob pripojenia

Downloads

UNIFLEX Advanced series – Light, quiet all-rounder with a wide range of applications

K tomu patrí

Vodiče pre nosiče energie – TRAXLINE®

Spoľahlivý, robustný s vysokou dostupnosťou. Profitujte z dlhoročných skúseností a z priebežnej optimalizácie overenou počas testov i v praxi. TRAXLINE^® vodiče pre kompetentné systémové poradenstvo ako aj servis po celom svete.

na TRAXLINE^®

Systémy nosičov energií pripravené na zapojenie – TOTALTRAX®

Od samostatných vedení až po komplexné systémy pripravené na zapojenie, v počte 1 až po série - po celom svete sú v nasadení tisícky osvedčených systémov. Prednosti TOTALTRAX^® systémov sú zjavné: jedna kontaktná osoba, jedno objednávacie číslo, dodávka just in time na želané miesto, krátke prestoje vďaka Plug & Play montáži.

na TOTALTRAX^®

Príslušenstvo

Spoľahlivé odvíjanie a optimálne kĺzanie pri dlhých pojazdoch

na Podporné kanály
na Vodiace kanály

Na optimálne umiestnenie pri dynamickom použití káblov

k Odľahčenie v ťahu

Služby

Konfigurátor produktu

Konfigurátor produktu

Konfigurovať efektívne, rýchlo a kompletne – výsledkom bude Váš systém nosičov energie s optimálnym pomerom cena / výkon
Online Konfigurátor produktuEngineer + zodpovedajúce CAD modely CADbez zmeny platformy

Konfigurátor produktu