to top Arrow Up
TSUBAKI
KABELSCHLEPP

Cable Carriers

All series at a glance

Series

MONO series
BASIC-LINE

MONO series

Cable carriers for standard applications

  • Cost-effective cable carrier
  • Easy and fast installation
  • Many types available immediately ex-stock world wide
  • Long service life
  • Great unsupported lengths compared to the unit size
  • High torsional rigidity
  • Easy to install
Inner height 10 – 15 mm
Inner width 6 – 40 mm
Bending radius 18 – 50 mm
Travel length 1.95 m
to the MONO series
QuickTrax® series
BASIC-LINE

QuickTrax® series

Compact and cost-effective cable carriers in two-component technology

  • Extremely fast and easy cable laying thanks to crossbar with film hinge
  • Each chain link consists of two different materials: 
        – Hard chain body made of glass-fibre reinforced material 
        – Crossbar with flexible film hinge made of elastic special plastic 
  • Sturdy cable carrier design
  • High torsional rigidity 
  • Very quiet through integrated noise damping
  • Extensive unsupported length
Inner height 20 mm
Inner width 15 – 65 mm
Bending radius 28 – 125 mm
Travel length 2.9 m
to the QuickTrax® series
UNIFLEX Advanced series
BASIC-LINE

UNIFLEX Advanced series

Light, quiet all-rounder with a wide range of applications*

  • Extensive unsupported lengths
  • High torsional rigidity
  • Good ratio of inner to outer width
  • Numerous custom material types for custom applications available
  • Easy assembly and fast cable laying
  • Assembly tools available
  • Stays with ball joint opening on both sides
  • Many possibilities for internal subdivision
  • Wear surfaces for gliding applications with extended travel lengths
Inner height 20 – 44 mm
Inner width 15 – 250 mm
Bending radius 28 – 300 mm
Travel length 7 m
to the UNIFLEX Advanced series
TKP35 series
BASIC-LINE

TKP35 series

Robust all-rounder with variable inner distribution

  • Robust and extremely rigid stroke system 
  • Quiet operation due to internal dampening system 
  • Weight-optimized cable carrier geometry
  • Interior without sharp edges, design that protects the cable 
  • Variable inner distribution 
  • Vertical moveable dividers or with arresting cams, can be attached at 2-mm increments (not Bi 16) 
  • Easy-to-open versions, left or right (not Bi 16)
  • Quick and easy to open
  • Optional strain relief can be fully integrated into the end connector
Inner height 32 mm
Inner width 16 – 50 mm
Bending radius 48 – 125 mm
Travel length 2.3 m
to the TKP35 series
TKK series
BASIC-LINE

TKK series

Dirt-repellent cable carriers made of plastic

  • High torsional rigidity
  • Optimised dividers to protect cables: rounded inner and outer profile
  • Extensive unsupported length
  • New dirt-resistant design of the chain links to protect against dust and chips
  • Smooth surface for optimum running
  • Closed and openable designs
  • Very short end connectors
  • Fixable dividers
  • Optimised stroke system
  • High side stability
  • Space-saving design for small spaces
Inner height 39 mm
Inner width 59 – 99 mm
Bending radius 46 – 95 mm
Travel length 4.8 m
to the TKK series
PROTUM® series
BASIC-LINE PLUS

PROTUM® series

Small, light cable carriers for unsupported applications

  • Quiet running through short pitch 
  • Low-vibration operation 
  • Ideal for short travel lengths and high travel speeds
  • Gentle on the cables due to virtually no polygon effect
  • Cost savings through easy cable installation
  • Installation of pre-assembled cables also possible
  • Belt with clip-on side parts 
  • Easy adaptation of the chain length
  • Low weight, good ratio between inner and outer width
Inner height 10 – 21.5 mm
Inner width 15 – 40 mm
Bending radius 18 – 72 mm
Travel length 1.5 m
to the PROTUM® series
EasyTrax® series
BASIC-LINE PLUS

EasyTrax® series

Extremely fast cable laying thanks to easy cable insertion

  • Very fast cable laying by simply pressing in the cables
  • Very high fill level through lateral swivelling of the lamella – lamellae do not swivel into the cable space
  • Each chain link consists of two different materials:
    – Hard chain body made of glass-fibre reinforced material
    – Lamellae with flexible film hinge made of special elastic plastic
  • Sturdy cable carrier design
  • High torsional rigidity
  • Extensive unsupported length
  • Very quiet through integrated noise damping
Inner height 4.6 – 25 mm
Inner width 7 – 78 mm
Bending radius 10 – 200 mm
Travel length 4.8 m
to the EasyTrax® series
K series
VARIO-LINE

K series

Cost-effective, robust cable carrier – suitable for large additional loads

  • Stable sidebands through robust link plate design
  • Encapsulated, dirt-resistant stroke system
  • Long service due to minimized hinge wear owing to the “life extending 2 disc principle“
  • Versions with aluminum stays available in 1 mm width sections up to 700 mm inner width
  • Versions with plastic stays available in 8 or 16 mm width sections
  • Large selection of vertical and horizontal stay separation options for your cables
Inner height 38 – 58 mm
Inner width 68 – 561 mm
Bending radius 75 – 385 mm
Travel length 8.4 m
to the K series
MASTER series
VARIO-LINE

MASTER series

Quiet and weight-optimized cable carriers

  • Low intrinsic weight
  • Favorable ratio of inner to outer dimensions
  • Versions with aluminum stays available in 1 mm width sections up to 800 mm inner width
  • Long service life due to minimized hinge wear owing to the “life extending 2 disc principle“
  • Extremely quiet through internal damping system
  • Variable pre-tensioning for the most varied applications is possible
Inner height 33 – 80 mm
Inner width 50 – 800 mm
Bending radius 60 – 500 mm
Travel length 7.9 m
to the MASTER series
M series
VARIO-LINE

M series

Variable cable carrier with extensive accessories and stay variants

  • Encapsulated, dirt-resistant stroke system
  • Durable sidebands through robust link plate design
  • Easy assembly of side bands through bars with easy-to-assemble locking bolts
  • Long service life due to minimized hinge wear owing to the “life extending 2 disc principle“
  • Large selection of vertical and horizontal stay systems and dividing options for your cables
  • Versions with aluminum stays in 1 mm width sections up to 800 mm inner width
  • Versions with plastic stays available in 4, 8 or 16 mm width sections
Inner height 19 – 87 mm
Inner width 24 – 800 mm
Bending radius 37 – 500 mm
Travel length 10.8 m
to the M series
TKHD series
VARIO-LINE

TKHD series

Heavy duty cable carriers for long travel lengths and high additional loads

  • Massive, enclosed, stain-repellend stop system
  • Massive sidebands through robust double fork-bracket-construction
  • Sidebands easy to assemble
  • Reinforced pin bore connection
  • Integrated noise damping
  • Quick and easy opening to the inside or outside 
  • for cable laying
  • Soil-resistant outer contour
  • Easy change of components
  • Maintenance-free
  • Symmetrical force curve in the sideband
  • Quiet and low-wear operating through polygon-­optimized contour and radii
Inner height 87 mm
Inner width 100 – 800 mm
Bending radius 250 – 360 mm
Travel length 13.5 m
to the TKHD series
XL series
VARIO-LINE

XL series

Cable carrier with large inside height

  • Sizes/dimensions
  • Low intrinsic weight
  • Optimum force transmission via the large-surface stroke system (2 disc principle)
  • Plastic side bands in combination with aluminum stays
  • Versions with aluminum stays available in 1 mm width sections up to 1000 mm inner width
  • Can be opened on both sides
  • Large selection of stay systems and separating options for cables
  • Optionally with strain relief
Inner height 108 mm
Inner width 200 – 1000 mm
Bending radius 250 – 550 mm
Travel length 11.75 m
to the XL series
QUANTUM® series
VARIO-LINE

QUANTUM® series

Light, extremely quiet and low-vibration for high speeds and accelerations

  • Cleanroom compatible: no links, no link wear
  • Extremely quiet, 31 db (A)*
  • Extremely light
  • For high accelerations up to 300 m/s2
  • For high operating speeds up to 40 m/s
  • Extremely long service life: ≥ 25 million motion cycles
  • TÜV type tested as per 2PfG 1036/10.97
  • Large selection of stay systems and separating options for cables
Inner height 28 – 72 mm
Inner width 28 – 600 mm
Bending radius 60 – 600 mm
Travel length 7.8 m
to the QUANTUM® series
TKR series
VARIO-LINE

TKR series

Extremely quiet and low-vibration for highly dynamic applications*

  • Long service life
  • Ideal for highly dynamic applications
  • High side stability
  • Cleanroom compatible
  • Modular design allows easy shortening and extending
Inner height 22 – 52 mm
Inner width 20 – 200 mm
Bending radius 40 – 200 mm
Travel length 4.9 m
to the TKR series
TKA series
TUBES-PLASTIC

TKA series

Chip-tight right to the end

  • Excellent cable protection in the connector area
  • Chip and dirt resistant due to smooth surfaces
  • Extensive unsupported length
  • High torsional rigidity
  • Low noise emission
  • Optional: On request, special material with protection against hot chips up to 850 °C
  • Numerous custom material types for custom applications available
  • Easy-to-open cover with simultaneously high retention force on the chain link during operation
  • Measurement scale for easy alignment of the dividers
  • TKA55: IP54 tested and certified*
Inner height 20.5 – 45 mm
Inner width 15 – 250 mm
Bending radius 55 – 300 mm
Travel length 6.5 m
to the TKA series
MT series
TUBES-PLASTIC

MT series

Variable, closed cable carrier with extensive range of accessories

  • Encapsulated, dirt-resistant stroke system
  • Stable side bands through robust link plate design
  • Easy assembly of side bands through bars with easy-to-assemble locking bolts
  • Long service life due to minimized hinge wear owing to the “life extending 2 disc principle”
  • Large selection of vertical and horizontal stay systems and separation options for your cables
  • Versions with aluminum cover system available in 1 mm width sections up to 800 mm inner width
  • Versions with plastic cover system available in 8 or 16 mm width sections
Inner height 26 – 87 mm
Inner width 24 – 800 mm
Bending radius 75 – 500 mm
Travel length 10.8 m
to the MT series
XLT series
TUBES-PLASTIC

XLT series

Tubes with variable cable carrier widths

  • Sizes/dimensions
  • Low intrinsic weight
  • Optimum force transmission via the large-surface stroke system (2 disc principle)
  • Plastic side bands in combination with aluminum stays
  • Versions with aluminum stays available in 1 mm width sections up to 1000 mm inner width
  • Can be opened on both sides
  • Large selection of separating options for cables and hoses
  • Optionally with strain relief
Inner height 105 mm
Inner width 200 – 1000 mm
Bending radius 300 – 550 mm
Travel length 11.75 m
to the XLT series
ROBOTRAX® System
3D-LINE

ROBOTRAX® System

Cable carrier for 3D movements

  • Suitable for three-dimensional swivel and rotation movements
  • Ideal for a long service life of the cables:
    – The bending radius does not fall below the minimum
    – The cables can be separated in three chambers
  • Also ideal for turntables
to the ROBOTRAX® System
LS/LSX series
STEEL-LINE

LS/LSX series

Cost-effective steel chains with light design

  • Weight-optimized one-part link plate design
  • Better value than comparable steel cable carriers
  • Significantly higher unsupported lengths compared to plastic cable carriers of a similar size
  • Integrated radius and pre-tension stops – in a good value design
  • Bolted stay systems, solid end connectors
  • Cover with steel band available on request
  • Also possible as a double band solution
  • Good corrosion resistance


The design
The weight-optimized link plate design makes the cable carriers very light yet highly sturdy. For the LS series, the unsupported length is significantly higher compared to plastic cable carriers of a similar size.

Inner height 54 – 58 mm
Inner width 54 – 584 mm
Bending radius 105 – 430 mm
Travel length 9.5 m
to the LS/LSX series
S/SX series
STEEL-LINE

S/SX series

Extremely robust and sturdy steel cable carriers

  • Extremely robust, sturdy steel cable carriers for heavy mechanical loads and rough environmental conditions
  • Side bands made of galvanized steel (S series) or corrosion-resistant and acid-resistant steel (SX series) in three qualities: ER 1 / ER 1S and ER 2
  • Very sturdy link plates, each consisting of two individual plates
  • Very extensive unsupported lengths even with large additional loads
  • Bolted stay systems, solid end connectors
  • Joint design with multi stroke system and hardened bolt
  • Explosion protection with classification EX II 2 GD as per ATEX RL


The design

Proven steel cable carriers with extremely sturdy link plates and dedicated joint design with multi stroke system and hardened bolt. The extremely sturdy design allows extensive unsupported lengths and high possible additional loads.

Inner height 26 – 578 mm
Inner width 35 – 1650 mm
Bending radius 75 – 2400 mm
Travel length 24.9 m
to the S/SX series
S/SX Tubes series
TUBES-STEEL

S/SX Tubes series

Extremely robust and sturdy covered steel cable carriers

  • Extremely robust, sturdy steel cable carriers for heavy mechanical loads and rough environmental conditions
  • Side bands made of galvanized steel (S series) or corrosion-resistant and acid-resistant steel (SX series) in three qualities: ER 1 / ER 1S and ER 2
  • Very sturdy link plates, each consisting of two individual plates
  • Very extensive unsupported lengths even with large additional loads
  • Joint design with multi stroke system and hardened bolt
  • Bolted stay systems, solid end connectors
  • Explosion protection with classification EX II 2 GD as per ATEX RL

The design
Proven steel cable carriers with extremely sturdy link plates and dedicated joint design with multi stroke system and hardened bolt. The extremely sturdy design allows extensive unsupported lengths and high possible additional loads.

Inner height 30 – 104 mm
Inner width 65 – 938 mm
Bending radius 115 – 1300 mm
Travel length 17.8 m
to the S/SX Tubes series
Contact
Please contact us:
Your contact:
Email: info@kabelschlepp.de

Quickfinder

For Cable Carriers

Material
  • Use
Design
  • Use
Inner height
Inner width
X Results
Use
Our Quickfinder supports you in finding the right cable carrier

Simply select your desired parameters and you will quickly get an overview of all suitable type series.

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
Product Configurator
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
CADenas
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Glossary
Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Technical information
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

download as PDF file
request the printed version of our catalogs and brochures
Quickfinder
Quickfinder
Close

Quickfinder

Our Quickfinder supports you in finding the right cable carrier. Simply select your desired parameters and you will quickly get an overview of all suitable type series.

Quickfinder
Product Configurator
Product Configurator
CADenas
CADenas
Glossary
Glossary
Technical information
Technical information
Literature
Literature
Quickfinder
Quickfinder