to top Arrow Up

MC1300 RMS

Aluminum stay RMS – frame stay reinforced

mc1300-rms_start.png

Properties

  • Aluminum profile bars with plastic ball joint for heavy loads and large cable carrier widths. Assembly without screws.
  • Available customized in 1 mm grid.
  • Inside/outside: Swivable and detachable.
test
Stay arrangement on every 2<sup>nd</sup> chain link

Stay arrangement on every 2nd chain link, standard (HS: half-stayed)

Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 1 mm increments
Bi 100 – 800 mm in 1 mm width sections

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
t
[mm]
hi
[mm]
hG
[mm]
hG'
[mm]
Bi
[mm] *
Bk
[mm]
BEF
[mm]
qk
[kg/m]
13087120127.5100 – 800Bi + 50Bi + 506.31 – 9.65
* in 1 mm width sections
KR
[mm]
150195240280320360400500
Order example
Order code

MC1300

400

RMS

360

6500

HS

Our technical support can provide help for gliding arrangements: technik@kabelschlepp.de

Inner distribution

Divider systems

The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).

For applications with lateral acceleration and lying on the side, the dividers can be attached by a fixing profile, available as an accessory (version B). The fixing profile must be installed at the factory.

Divider system TS0

without height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A15.51510
B18.515105

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS0

Divider system TS1

with continuous height separation
Vers.
aT min
[mm]
aT max
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
A15.52515102
B18.525151052

The dividers can be moved within the cross section (version A) or fixed (version B).

Divider system TS1

Divider system TS3

with partial height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
nT min
A15.516/42*82

* for aluminum partitions

With grid distribution (1 mm grid). The dividers are attached by the height separation, the grid can be moved in the cross section.

Divider system TS3
Divider system TS3

Aluminum partitions with 1 mm increments with ax > 42 mm are also available.

ax (center distance of dividers) [mm]
ac (nominal width of inner chamber) [mm]
16
8
18
10
23
15
28
20
32
24
33
25
38
30
43
35
48
40
58
50
64
56
68
60
78
70
80
72
88
80
96
88
112
104
128
120
144
136
160
152
176
168
192
184
208
200

When using plastic partitions with ax > 112 mm, we recommend an additional center support with a twin divider (ST = 5 mm). Twin dividers are also suitable for retrofitting in the partition system. The height separations VR8 and VR9 are not possible when using twin dividers.

Order example
Order code

TS3

A

3

K1

K5

34

38

VD1

VD3

Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

M1300 End Connector
Important information

Recommended tightening torque: 54 Nm for cheese-head screws ISO 4762 - M10 - 8.8

M1300 End Connector
Connection point

F – fixed point
M – driver

Connection type

U – universal mounting bracket

Order example
Order code

UMB

F

A

UMB

M

A

End connector

UMB

UMB

Connection point

F

M

Connection type

A

A

Important information

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

Subject to change.
Contact
Please contact us:
Your contact: