to top Arrow Up

MT0475 RDD 01

Plastic cover RDD 01 – cover with hinge in the inner radius

mt0475-rdd-1_start.png

Properties

  • Plastic cover system with hinge for light and medium loads. Assembly without screws.
  • Available customized in 8 mm sections.
  • Outside: release by rotating 90°.
  • Inside: swivable to both sides.
test
Stay arrangement on every chain link

Stay arrangement on each chain link (VS: fully-stayed)

Inner width (B<sub>i</sub>) in 8 mm increments
Bi 24 – 280 mm in 8 mm width sections

Dimensions

Dimensions
Important information

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length
Cable carrier length LK: LK ≈ LS/2 + LB
Cable carrier length Lk rounded to pitch t
t
[mm]
hi
[mm]
hG
[mm]
Bk
[mm]
BEF
[mm]
qk
[kg/m]
47.52639Bi + 17Bi + 170.90 – 4.41
* in 8 mm width sections
Bi
[mm]
24324048566472808896
104112120128136144152160168176
184192200208216224232240248256
264272280
KR
[mm]
75100130160200250300
Order example
Order code

MT0475

128

RDD 01

100

1425

VS

Inner distribution

Divider systems

As a standard, the divider system is assembled at every 2nd chain link.

For applications with lateral acceleration and laying on the side, the dividers or the complete divider system (dividers with height separations) are fixed in the cross section. The arresting cams click into place in the locking grids in the crossbars (version B).

Divider system TS0

without height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B67.858
Divider system TS0

Divider system TS1

with continuous height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B67.8582

The dividers are fixed in the cross section (version B).

Divider system TS1

Divider system TS2

with partial height separation
Vers.
aT min
[mm]
ax min
[mm]
ac min
[mm]
ax grid
[mm]
nT min
B128*/245.2*/21.282

* for VR0

With grid distribution (8 mm grid). The dividers are fixed by the height separation, the grid is fixed in the cross section (version B).

Divider system TS2
Order example
Order code

TS2

B

3

K1

K4

34

38

VR1

VR3

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [nT]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).

If using divider systems with height separation (TS1 – TS2), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.

 

End connectors

MT0475 End connector - plastic/steel (with strain relief)
MT0475 End connector - plastic/steel (with strain relief)
Bi
[mm]
X
[mm]
nz
40
17.53
56
21.54
80
17.56
104
198
128
19.59
152
17.511
192
18.514

Other widths only available without strain relief.

MT0475 End connector - plastic/steel (with strain relief)
Connection point

– fixed point
– driver

Connection type

– threaded joint outside (standard)
– threaded joint inside

Connection surface

– connection surface inside

Order example
Order code

Plastic/steel

F

A

I

Plastic/steel

M

A

I

End connector

Plastic/steel

Plastic/steel

Connection point

F

M

Connection type

A

A

Connection surface

I

I

MT0475 End connector - plastic/steel
MT0475 End connector - plastic/steel
MT0475 End connector - plastic/steelMT0475 End connector - plastic/steel
Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

I – connection surface inside
A – connection surface outside

Order example
Order code

Plastic/steel

F

A

A

Plastic/steel

M

U

 

End connector

Plastic/steel

Plastic/steel

Connection point

F

M

Connection type

A

U

Connection surface

A

Important information

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator
Product Configurator
Close

Product Configurator

  • Efficient, quick and complete configuration ­ the result is your individual product with an excellent price-performance ratio
  • Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal
CADenas
CADenas
Close

CADenas

  • Decrease your engineering times
  • Accelerate your design processes
  • Configure with original data directly from the manufacturer
  • Providing 3D component models in a variety of CAD formats
Glossary
Glossary
Close

Glossary

Cable Carriers – Overview of general abbreviations and pictographs

Technical information
Technical information
Close

Technical information

Configuration guidelines:

  • Selecting a suitable cable carrier
  • Placement guidelines for cables and hoses
  • Installation variants
Literature
Literature
Close

Literature

The latest TSUBAKI KABELSCHLEPP information material:

Subject to change.
Contact
Please contact us:
Your contact: