MT0475 RDD 02

Plastic cover RDD 02 – cover with hinge in the outer radius

Properties

Plastic cover system with hinge for light and medium loads. Assembly without screws.
Available customized in 8 mm sections.
Outside: swivable to both sides.
Inside: release by turning 90°.

Stay arrangement on each chain link (VS: fully-stayed)

B_i 24 – 280 mm in 8 mm width sections

All pictographs

Dimensions

The maximum cable diameter strongly depends on the bending radius and the desired cable type. Please contact us.

Calculating the cable carrier length

Cable carrier length L_K: L_K≈ L_S/2 + L_B

Cable carrier length L_k rounded to pitch t

t [mm]	h_i [mm]	h_G [mm]	B_k [mm]	B_EF [mm]	q_k [kg/m]
47.5	26	39	B_i + 17	B_i + 17	0.90 – 4.41

^* in 8 mm width sections

B_i [mm]
24	32	40	48	56	64	72	80	88	96
104	112	120	128	136	144	152	160	168	176
184	192	200	208	216	224	232	240	248	256
264	272	280

KR [mm]
75	100	130	160	200	250	300

Order example

MT0475

Type

128

B_i [mm]

RDD 02

Stay variant

100

KR [mm]

1425

L_k [mm]

Stay arrangement

Inner distribution

Divider systems

As a standard, the divider system is assembled at every 2^nd chain link.

For applications with lateral acceleration and laying on the side, the dividers or the complete divider system (dividers with height separations) are fixed in the cross section. The arresting cams click into place in the locking grids in the crossbars (version B).

Divider system TS0

without height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	6	7.8	5	8	–

Divider system TS1

with continuous height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	6	7.8	5	8	2

The dividers are fixed in the cross section (version B).

Divider system TS2

with partial height separation

Vers.	a_{T min} [mm]	a_{x min} [mm]	a_{c min} [mm]	a_{x grid} [mm]	n_{T min}
B	12	8^*/24	5.2^*/21.2	8	2

^* for VR0

With grid distribution (8 mm grid). The dividers are fixed by the height separation, the grid is fixed in the cross section (version B).

Order example

TS2

Divider system

Version

n_T

Chamber

a_x

VR1

VR3

Height separation

Please state the designation of the divider system (TS0, TS1 …), version and number of dividers per cross section [n_T]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [a_T/a_x] (as seen from the driver).

If using divider systems with height separation (TS1 – TS2), please also state the positions (e.g. VD23) viewed from the left driver belt. You are welcome to add a sketch to your order.

End connectors

End connector – plastic/steel (with strain relief)

Link end connector made of plastic, end connector made of sheet steel with screw-fixed aluminum strain relief. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

B_i [mm]	X [mm]	n_z
40	17.5	3
56	21.5	4
80	17.5	6
104	19	8
128	19.5	9
152	17.5	11
192	18.5	14

Other widths only available without strain relief.

MT0475 End connector - plastic/steel (with strain relief)

Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside

Connection surface

I – connection surface inside

Order example

Plastic/steel

End connector

Connection point

Connection type

Connection surface

End connector

Plastic/steel

Connection point

Connection type

Connection surface

End connectors – plastic/steel

Plastic link end connector, steel end connector. The connection variants on the fixed point and on the driver can be combined and, if required, changed afterwards.

Connection point

F – fixed point
M – driver

Connection type

A – threaded joint outside (standard)
I – threaded joint inside
F – flange connection

Connection surface

I – connection surface inside
A – connection surface outside

Order example

Plastic/steel

End connector

Connection point

Connection type

Connection surface

End connector

Plastic/steel

Connection point

Connection type

Connection surface

We recommend the use of strain reliefs at the driver and fixed point.

Downloads

MT series – Variable, closed cable carrier with extensive range of accessories

Matching with

Cables for cable carriers – TRAXLINE®

Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE^® cables stand for competent system-supply with worldwide on-site service.

to TRAXLINE^®

Ready-to-connect cable carrier systems – TOTALTRAX®

From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX^® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.

to TOTALTRAX^®

Accessories

Reliable unrolling and optimum gliding for long travel lengths

to Support trays
to Guide channels

For optimum placement with dynamic use of cables

to Strain relief devices

Services

Product Configurator

Product Configurator

Efficient, quick and complete configuration the result is your individual product with an excellent price-performance ratio
Product configurator OnlineEngineer + suitable CAD model from CADenas without having to exit the portal

Product Configurator