The maximum cable diameter strongly depends on the bending radius and the desired cable type.
Please contact us.
Design 040 is not suitable for gliding arrangements.
|66.5||44||60||Bi + 22||1.67 – 2.70|
The divider system is mounted on every 2nd chain link as a standard. As a standard, dividers or the complete divider system (dividers with height separations) are movable in the cross section (version A).
For applications with lateral acceleration and lying on the side, divider with arresting cams are available.
The locking cams click into place in the locking grids in the crossbars (version B).
Number of dividers for design 020 depending on Bi
Version B: not for design 020
Trennsteganzahl bei Bauart 020 abhängig von Bi
* nicht Bauart 020
* not for design 020
* for aluminum partitions
The dividers are fixed with the partitions. The entire divider system can be moved in the cross section.
Aluminum partitions in 1 mm width sections with ax > 42 mm are also available.
|ax (center distance of dividers) [mm]|
|ac (nominal width of inner chamber) [mm]|
When using partitions with ax> 112 mm, we recommend an additional central support with a twin divider. The height separations VD4 and VD5 are not possible when using twin dividers.
Please state the designation of the divider system (TS0, TS1,...), version and number of dividers per cross section [nT ]. In addition, please also enter the chambers [K] from left to right, as well as the assembly distances [aT/ax] (as seen from the driver).
If using divider systems with height separation (TS1 – TS3), please also state the positions [e.g. VD23] viewed from the left driver belt. You are welcome to add a sketch to your order.
The universal mounting brackets (UMB) are made from plastic and can be mounted from above, from below or on the face side.
Recommended tightening torque:
5 Nm for screws M5 - 8.8
|2 x 3|
|2 x 5|
|2 x 7|
|2 x 9|
|2 x 11|
|2 x 13|
The end connectors are optionally also available with strain relief comb or with C-rail Art. no. 3931 (1 on each side) for clamps. Please state when ordering.
F – fixed point
M – driver
U – universal mounting bracket
We recommend the use of strain reliefs at the driver and fixed point.
The plastic end connectors can be connected from above or below. The connection type can be changed by altering the position of the end connector.
Recommended tightening torque: 15 Nm for screws M8 - 8.8
|2 x 4|
|2 x 6|
|2 x 8|
|2 x 10|
|2 x 12|
|2 x 14|
|2 x 16|
|2 x 18|
|2 x 20|
The end connectors are optionally also available without strain relief comb. Please state when ordering.
F – fixed point
M – driver
A – threaded joint outside (standard)
I – threaded joint inside
H – threaded joint, rotated 90° to the outside
K – threaded joint, rotated 90° to the inside
Reliable, robust with high availability. Your benefit from many years of experience combined with ongoing optimization, proven in tests and praxis. TRAXLINE® cables stand for competent system-supply with worldwide on-site service.to TRAXLINE®
From pre-assembled cables to complex, ready-to-connect systems, from lot size 1 to series – worldwide thousands of KABELSCHLEPP systems are reliably in use. The benefits of TOTALTRAX® systems are obvious: just one person of contact, one order number, delivery just-in-time to your production facility, shortest downtimes thanks to plug&play installation.to TOTALTRAX®
Reliable unrolling and optimum gliding for long travel lengthsto support trays and guide channels
Cable Carriers – Overview of general abbreviations and pictographs
The latest TSUBAKI KABELSCHLEPP information material: